Why Learning Plumbing Basics is Crucial for Installing a Bathtub
Why Learning Plumbing Basics is Crucial for Installing a Bathtub
Blog Article
Right here below you can discover additional extremely good material about How to Install a Bathtub.
Installing a bath tub isn't precisely rocket science, yet it does need solid plumbing, woodworking, and occasionally, tiling abilities. Replacing an old bath tub with a new one is additionally a moderately difficult job. If the old tub is readily obtainable, the task can move quickly; if you need to open a wall surface to get rid of the old tub and also position the new bath tub, the task is a lot harder. In either situation, the task is within a house handyman's abilities, although you will require a helper to leave the old tub as well as embeded in the new one. See to it you have certified on your own for the task and also fit trying it. Instead of employing a service provider to take over a halfway-completed job, it is much better to take into consideration using one prior to you begin. Chances are you may need a professional plumber to make tube connections.
This post will assist you set up a new bathtub in your bathroom if you have currently acquired a brand-new tub and do not need to change the setup of your previous water system pipelines.
Your tools and also material checklist ought to make up the following:
Removing Old Taps
If you require to replace old faucets with brand-new ones as a part of your setup, after that the first thing you need to do is disconnect the water. After doing so, activate the taps to drain any water staying in the system. The procedure of removing the existing taps can be fairly troublesome because of the limited accessibility that is frequently the situation.
Utilize a container wrench (crowsfoot spanner) or a faucet device to reverse the nut that links the supply pipes to the taps. Have a cloth prepared for the staying water that will come from the pipes. Once the supply pipes have actually been gotten rid of, utilize the exact same tool to loosen the nut that holds the faucets onto the bath/basin. You will need to quit the single taps from transforming throughout this procedure. When the taps have been eliminated, the holes in the bath/basin will need to be cleaned up of any old securing substance.
Before moving on to fit the brand-new taps, contrast the pipeline connections on the old taps to the new taps. If the old faucets are longer than the new taps, then a shank adapter is needed for the brand-new faucets to fit.
Fitting New Taps
If the tails of the new taps are plastic, then you will certainly need a plastic adapter to stop damage to the string. One end of the adapter fits on the plastic tail of the tap and also the various other end provides a connection to the existent supply pipelines.
If you need to fit a monobloc, after that you will certainly call for decreasing couplers, which links the 10mm pipeline of the monobloc to the common 15mm supply pipeline.
Next, position the tap in the placing opening in the bath/basin making sure that the washers are in area in between the tap and the sink. Safeguard the tap in position with the maker offered backnut. Once the faucet is securely in position, the supply pipes can be attached to the tails of the taps. The faucets can either be connected by utilizing corrugated copper piping or with normal faucet adapters. The former kind should be linked to the faucet ends initially, tightening up only by hand. The supply pipes can later on be attached to the other end. Tighten both ends with a spanner after both ends have actually been attached.
Installing the Tub
Making use of the two wood boards under its feet, put the bath tub in the required placement. The wooden boards are helpful in uniformly spreading the weight of the bath tub over the location of the boards instead of concentrating all the weight onto 4 small factors.
The next goal is to ensure that the bathtub is leveled all round. This can be achieved by inspecting the spirit level and also adjusting the feet on the bathtub until the level reviews degree.
To mount taps, fit the bottom of the outermost versatile tap adapter to the ideal supply pipe by making a compression join; after that do the same for the various other tap.
Switch on the water supply and also examine all joints as well as new pipework for leaks and tighten them if required. Fill up the bathtub and likewise inspect the overflow outlet and the regular electrical outlet for leaks.
Lastly, repair the bath paneling as explained in the producer's user's manual. Tiling and sealing around the tub needs to wait till the bathtub has been utilized at the very least when as this will certainly resolve it right into its final placement.
Preparing for the Installment
To start with, the supporting frame supplied with the bath should be fitted (if required) according to the manufacturer's instructions. Next off, fit the faucets or mixer to the tub. When fitting the tap block, it is essential to ensure that if the tap features a plastic washing machine, it is fitted between the bathroom and also the taps. On a plastic bath, it is additionally practical to fit a supporting plate under the faucets system to stop stress on the bathtub.
Fit the versatile tap ports to the bottom of the two faucets using 2 nuts and also olives (in some cases provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the electrical outlet through the hole in the bathroom. Make use of the nut supplied by the producer to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the versatile overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which should be fitted inside the bath. Ensure you use all of the supplied washing machines.
Link the catch to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Connect the bottom of the overflow tube in a similar manner.The bathroom ought to currently be ready to be suited its last position.
Tiling Around the Bathtub
In the location where the bathroom satisfies the tile, it is essential to secure the joins with a silicone rubber caulking. This is important as the installation can move sufficient to split a rigid seal, creating the water to permeate the wall in between the bath and also the tiling, resulting in complications with moisture and also possible leakages to the ceiling listed below.
You can select from a selection of coloured sealers to blend in your fixtures and also fittings. They are sold in tubes and also cartridges, and are capable of securing voids approximately a size of 3mm (1/8 inch). If you have a larger gap to load, you can fill it with twists of soaked paper or soft rope. Remember to constantly fill up the tub with water prior to sealing, to allow for the movement experienced when the tub is in use. The sealer can crack fairly early if you do not take into consideration this motion before sealing.
Conversely, ceramic coving or quadrant floor tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are additionally quickly offered on the market. It is suggested to fit the ceramic tiles using water-resistant or water-proof sticky and grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Hopefully you enjoyed reading our part about How to Install a Bathtub Yourself. Thanks for taking time to read our short article. Do you know about another individual who is fascinated about the subject? Take a moment to promote it. We thank you for reading our article about How to Install a Bathtub Yourself.
Dial, we'll handle! Report this page